Two New Knight Pro Twin Heavy Duty V Type Manure Spreaders In Stock
At Binkley & Hurst Bros. For Immediate Delivery
In Stock For Delivery Now!
Model 8018 Approx. 400 Bu. Or 1800 Gallon, Model 8030 Approx. 600 Bu. or 3080 Gal.
Retire Your Current Spreaders!
The 8000 Series Pro Twin Slingers can handle
a wider range of materials than any other spreader...
With the patented twin auger design,
matenal circulates inside the unit This
unique action helps keep the load level
during normal operation as well as during
start up, fine spreading, and closed-door
turns
As a result of the twin auger system and
the steep angle sides, matenal bndgmg
and excess forward movement of matenal
are virtually elmunated,evenmpen packed
and sticky feed lot matenal
Examine the matenal flow in the
illustration below and note that the left
auger moves matenal forward to the
discharge hammers The slightly raised
nght auger moves the matenal rearward
while keeping the left auger evenly
charged with matenal It is this patented
circulaung action that makes the ProTwm
so effective in handling the toughest
matenal encountered in most applications
Twin Auger Design History
The first Pro Twin model, the Industrial
8030 unit, was introduced m the summer
of 1993 The total acceptance of the
Pro Twin Slinger by agncultural and
mdustnal operators in handling the
toughest waste material has been
phenomenal
BINKUYkHURST ,M ?S£?!rSSr“-
P i- BROS. INC.-' (7!7)62M705
rn HHiMWte ftatfen M.
UM. MIIM> __ HUH WB
(71?r626-4705
Fax 717-626-0996 i-WMtr-sm
Trade-In Your Good Used Late Model Box Si
Ongmally, the 8030 Pro Twin was
targeted for mdustnal use Today, the same
design has been adapted to smaller models
to meet the matenal handling needs of
most applications. All of these models
handle a wide range of materials, from
lough pen pack and sbeky feed lot matenal
to slurry types of manure, as well as
difficult industrial materials,
. «'gUßSUi || *T*'
i IS* 7 ,
Front Drive Compartment*
Simple Massive
Reduction Drive
Each of the Pro Twin models is designed
for maximum, high torque output. The
fully sealed front oil bath enclosures help
assure that chains and sprockets remain
clean and well lubricated. The auger and
expeller shafts are sealed to help
eliminate oil contamination. Polyethylene
type spring loaded chain tighteners are
140Mi70297t
If It’s Snow Removal Or Heavy Duty Excavating, You
Need A Rhino Blade From Binkley & Hurst Bros. Now!
* < <r '>>z > *) /'
133 R utlt* V pA 17543° Rd ‘ S
BRO S i INC. -* (717) ggT g*,
1-800-487-2978 Fax 717 ' 626 ’°" 6 *B®
used on all dnveline chains for positive
alignment and long life. Bearings can
easily be greased through the external
grease banks without removing the front
drive shield. Splined shafts have been
used in all high-torque areas to provide
added strength and reliability
PTO Dnveline
Conatant Velocity PTO
with Overload Clutch
Both 540 and 1000 RPM drivelines
incorporate a constant velocity joint to
provide a smooth transfer of power from
the tractor to the unit This relieves uneven
stress on the drive train during normal
turns and during operation over uneven
terrain. The overload clutch provides
protection for the expeller shaft and
initial drive components. (There is no
shear pin in the expeller drive)
Forged-Steel
Hammer
Each hammer has
a nylon bushing and
a replaceable man
ganese steel wear
plate
Srarm Plan.
Aimutet/Kfieemtet
'V '
% ,
. ,
■l* '
A support stand Is standard on th« 800 Blade to provide safer
storage and unit hook-up The moldboard and replaceable cut
ting edge form a constant curvature to cut and roll the material
being worked more efficiently Optional equipment includes
quick-tach end plates, skid shoes, and CAT tl quick coupler
bushings
Hammer Discharge
Patented Free Swinging
Hammer Expeller
The expeller on all Pro Twin models
features IS forged steel hammers
mounted on a 2'/ 2 " shaft. The hammers
pivot on Vi" bolts with nylon anti-seize
type bushings that allow free
movement The expeller routes at over
* rYTI
RHINO REAR BLADES
With Hydraulics For Tractors Rated From
75-150 DBHP. Available w/7% B’, 9’ & 10’
Moldboards * Rhino Model LR 6’
Also Smaller Heavy 7’-8* 3 Pt. Blades
Built Units In Stock R 950 w/B’-9’ Blade
*>> <-v*»
reader Toda
800 RPM allowing each eight pound
hammer to swing down into the material,
peeling it off and slinging it underhand
in a fine spread pattern with no clumps.
The 3” wide, free swinging hammers
absorb shock and tolerate most foreign
objects Each hammer is faced with a
work-hardening manganese steel wear
plate for longer life and low cost
replacement. The adjustable shroud
allows easy hammer clearance setting
for optimum spread pattern width. This
proven hammer expeller design enables
fine spreading control and material
calibration through the combination of
the hydraulic door opening and ground
speed
I, Srturday, Ftbrutry 11,1985*017
The 800 Blade features mainframe swing, moldboard pivot, and
moldboard tilt to fit a wide range of applications The blade
can be offset a maximum of 30" from the center line of the tree
tor for working outside the tractor tire The moldboard can be
pivoted a full 360 degrees for backfilling or working in hard-to
reach areas
T% l
The nght auger is driven at the rear
and is shear pm protected Bearings,
chamsand sprockets are easily accessible
for routine maintenance
•Shields removed for illustration only
Do not operate without shields in place and functioning
Quality
Your
m
Rear Dnve Compartment*